氣體增壓泵安裝時應該注意哪些問題

1.安裝：氣體增壓泵安裝過程中，請參考技術參數中的各接口尺寸，避免異物進入泵內，保持進出口的清潔。1. Installation: gas booster pump installation process, please refer to the technical parameters of each interface dimension, avoid foreign bodies into the pump, maintain the cleanness of the import and export.2.氣源質量標準：請選擇潔凈氣源，以保證泵能持續穩定的工作。氣源請滿足下表要求：2. The air quality standards: please select clean air, to ensure that the pump can work steadily. Air please meet the requirement in the table below:3.氣源潤滑：氣體增壓泵在出廠時，所有運動部分已經抹有適量潤滑油，一般不再需要潤滑，如長期使用干燥的壓縮氣體驅動，建議在二聯體的油杯內加入適量的潤滑油，進行油霧潤滑。3. Air lubrication, gas booster pump in the factory, all moving parts have to have a moderate amount of lubricating oil, generally no longer need lubrication, such as long-term use of dry compressed gas drive, suggest that in the second couplet body add lubricating oil in the oil cup, oil mist lubrication.4.氣源壓力：氣體增壓泵的最小驅動壓力為1.5-2bar，最大設計驅動壓力為10bar。建議使用氣壓在6-8bar之間?？赏ㄟ^(guò)調整調壓閥的壓力，以達到需求的使用壓力。4. Air pressure: the minimum driving pressure gas booster pump is 1.5-2 bar, the maximum design driven pressure to 10 bar. Recommend the use of air pressure between 6 to 8 bar. By adjusting the pressure regulating valve, in order to achieve the use of demand pressure.泵的驅動壓力絕對不能超過10bar，如果是通過管道氣進行驅動的，一定有可靠的減壓閥及安全閥。Pump driven by pressure must not more than 10 bar, if is driven by gas pipeline, there must be a reliable pressure reducing valve and relief valve.5.連接管路：根據氣體增壓泵http://www.jujiaso.cn/的輸出壓力、流量，選擇合適的進出口連接管路，確保能承受泵的最大輸出壓力、流量。泵的驅動口連接管路通徑應略大于泵的驅動口連接螺紋的公稱尺寸，如果連接通徑變小，將極大地影響泵的工作效率！5. Connect line: according to the output of the gas booster pump pressure, flow, select the appropriate connection line of imports and exports, to ensure that can withstand the maximum output pressure and flow of the pump. Pump drive mouth connection pipe size should be slightly bigger than the pump drive joint thread nominal size, smaller, if the connection size will greatly influence the work efficiency of the pump!

當前位置：首頁 >> 公司動態 >> 行業資訊發布時間： 2014-08-25
上一篇：氣體增壓泵增壓系統典型應用下一篇：氣體增壓泵解決了工廠內部氣源壓力不足的問題